CMU
UM


PID Tutorial

Introduction
The three-term controller
The characteristics of P, I, and D controllers
Example Problem

Open-loop step response
Proportional control
Proportional-Derivative control
Proportional-Integral control
Proportional-Integral-Derivative control
General tips for designing a PID controller


Key Matlab Commands used in this tutorial are: step cloop
Note: Matlab commands from the control system toolbox are highlighted in red.

Introduction

This tutorial will show you the characteristics of the each of proportional (P), the integral (I), and the derivative (D) controls, and how to use them to obtain a desired response. In this tutorial, we will consider the following unity feedback system:

The three-term controller

The transfer function of the PID controller looks like the following:


First, let's take a look at how the PID controller works in a closed-loop system using the schematic shown above. The variable (e) represents the tracking error, the difference between the desired input value (R) and the actual output (Y). This error signal (e) will be sent to the PID controller, and the controller computes both the derivative and the integral of this error signal. The signal (u) just past the controller is now equal to the proportional gain (Kp) times the magnitude of the error plus the integral gain (Ki) times the integral of the error plus the derivative gain (Kd) times the derivative of the error.

This signal (u) will be sent to the plant, and the new output (Y) will be obtained. This new output (Y) will be sent back to the sensor again to find the new error signal (e). The controller takes this new error signal and computes its derivative and its integral again. This process goes on and on.

The characteristics of P, I, and D controllers

A proportional controller (Kp) will have the effect of reducing the rise time and will reduce ,but never eliminate, the steady-state error. An integral control (Ki) will have the effect of eliminating the steady-state error, but it may make the transient response worse. A derivative control (Kd) will have the effect of increasing the stability of the system, reducing the overshoot, and improving the transient response. Effects of each of controllers Kp, Kd, and Ki on a closed-loop system are summarized in the table shown below.

CL RESPONSE
RISE TIME
OVERSHOOT
SETTLING TIME
S-S ERROR
Kp
Decrease
Increase
Small Change
Decrease
Ki
Decrease
Increase
Increase
Eliminate
Kd
Small Change
Decrease
Decrease
Small Change

Note that these correlations may not be exactly accurate, because Kp, Ki, and Kd are dependent of each other. In fact, changing one of these variables can change the effect of the other two. For this reason, the table should only be used as a reference when you are determining the values for Ki, Kp and Kd.

Example Problem

Suppose we have a simple mass, spring, and damper problem.

The modeling equation of this system is

(1)

Taking the Laplace transform of the modeling equation (1)

The transfer function between the displacement X(s) and the input F(s) then becomes

Let

Plug these values into the above transfer function

The goal of this problem is to show you how each of Kp, Ki and Kd contributes to obtain

Open-loop step response

Let's first view the open-loop step response. Create a new m-file and add in the following code:

Running this m-file in the Matlab command window should give you the plot shown below.

The DC gain of the plant transfer function is 1/20, so 0.05 is the final value of the output to an unit step input. This corresponds to the steady-state error of 0.95, quite large indeed. Furthermore, the rise time is about one second, and the settling time is about 1.5 seconds. Let's design a controller that will reduce the rise time, reduce the settling time, and eliminates the steady-state error.

Proportional control

From the table shown above, we see that the proportional controller (Kp) reduces the rise time, increases the overshoot, and reduces the steady-state error. The closed-loop transfer function of the above system with a proportional controller is:

Let the proportional gain (Kp) equals 300 and change the m-file to the following:

Running this m-file in the Matlab command window should gives you the following plot.


Note: The Matlab function called cloop can be used to obtain a closed-loop transfer function directly from the open-loop transfer function (instead of obtaining closed-loop transfer function by hand). The following m-file uses the cloop command that should give you the identical plot as the one shown above.

The above plot shows that the proportional controller reduced both the rise time and the steady-state error, increased the overshoot, and decreased the settling time by small amount.

Proportional-Derivative control

Now, let's take a look at a PD control. From the table shown above, we see that the derivative controller (Kd) reduces both the overshoot and the settling time. The closed-loop transfer function of the given system with a PD controller is:

Let Kp equals to 300 as before and let Kd equals 10. Enter the following commands into an m-file and run it in the Matlab command window.

This plot shows that the derivative controller reduced both the overshoot and the settling time, and had small effect on the rise time and the steady-state error.

Proportional-Integral control

Before going into a PID control, let's take a look at a PI control. From the table, we see that an integral controller (Ki) decreases the rise time, increases both the overshoot and the settling time, and eliminates the steady-state error. For the given system, the closed-loop transfer function with a PI control is:

Let's reduce the Kp to 30, and let Ki equals to 70. Create an new m-file and enter the following commands.

Run this m-file in the Matlab command window, and you should get the following plot.

We have reduced the proportional gain (Kp) because the integral controller also reduces the rise time and increases the overshoot as the proportional controller does (double effect). The above response shows that the integral controller eliminated the steady-state error.

Proportional-Integral-Derivative control

Now, let's take a look at a PID controller. The closed-loop transfer function of the given system with a PID controller is:

After several trial and error runs, the gains Kp=350, Ki=300, and Kd=50 provided the desired response. To confirm, enter the following commands to an m-file and run it in the command window. You should get the following step response.

Now, we have obtained the system with no overshoot, fast rise time, and no steady-state error.

General tips for designing a PID controller

When you are designing a PID controller for a given system, follow the steps shown below to obtain a desired response.
  1. Obtain an open-loop response and determine what needs to be improved
  2. Add a proportional control to improve the rise time
  3. Add a derivative control to improve the overshoot
  4. Add an integral control to eliminate the steady-state error
  5. Adjust each of Kp, Ki, and Kd until you obtain a desired overall response. You can always refer to the table shown in this "PID Tutorial" page to find out which controller controls what characteristics.
Lastly, please keep in mind that you do not need to implement all three controllers (proportional, derivative, and integral) into a single system, if not necessary. For example, if a PI controller gives a good enough response (like the above example), then you don't need to implement derivative controller to the system. Keep the controller as simple as possible.

User Feedback

We would like to hear about difficulties you had with the tutorials, suggestions you have for improvement, errors that you found, or any other comments that you have. This feedback is anonymous; include your email address if you want a reply.


PID Examples
Cruise Control | Motor Speed | Motor Position | Bus Suspension | Inverted Pendulum | Pitch Controller | Ball and Beam

Tutorials
Basics | Modeling | PID | Root Locus | Frequency Response | State Space | Digital Control | Examples

HOME INDEX COMMANDS

8/26/97 DK